Serving the Odessa area  ·  (432) 248-0371  ·  Open Mon-Sun 7am-7pm
📞 (432) 248-0371 Free Quote

Metal Roofing in Wink, TX (79789) · Local Professionals

Odessa Metal Roofing · Fast response in Wink and the Odessa area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+243Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Wink is a small oil-town community west of Odessa where the housing stock is mostly older frame and brick homes built during the oil booms, many with low-pitched shingle roofs that have taken decades of sun, wind, and hail. The flat, sandy caliche ground and wide open lots mean roofs here face dust storms, intense UV, and spring wind events that test every fastener and seam. If you live near Winkler County Airport or along the main drag through town, you know the sound of a metal roof after a hailstorm is different from shingle, and that is why more folks here are switching to metal.

Homeowners in Wink (79789) call Odessa Metal Roofing because we understand the specific wear patterns on these older roofs: failed fasteners on corrugated panels, wind-lifted shingles on low-slope porches, and flashing gaps around chimneys that have been patched one too many times. We are based in Odessa and serve Wink and the surrounding areas, so we know the drive and the local conditions. When you need a straight answer about repair or replacement, call us at (432) 248-0371.

Metal Roofing in Wink (79789)

Wink sits on flat, sandy caliche soil with little natural drainage, so water tends to pool around foundations after a hard rain. That makes proper roof pitch and flashing details critical, especially on the older bungalows and ranch homes where the original roof structure may have settled. Many properties have detached shops, carports, and barns with corrugated panels that have been re-fastened a time or two, and the wind out here will find every loose screw. We also see a lot of manufactured homes and oilfield-worker housing where metal roofs are a practical upgrade over aging shingles. The intense summer heat above 100 degrees and the dust that settles in seams mean we pay close attention to sealants and fastener selection.

Our team has worked throughout Wink and the Permian Basin, from small repair jobs on a leaking porch roof to full standing seam installations on brick ranches. We know the local building department requirements vary and always verify with the city before starting, and we can help document damage for insurance claims without making promises about coverage. We are fully insured with general liability and workers' compensation, so you are protected.

Our services in Wink

How a Job Works in Wink

Step 1: You call us at (432) 248-0371 or request a free estimate. We schedule an on-site assessment at your Wink property, usually within a few days, and we inspect the roof, attic if accessible, and flashing details. We give you a written scope and price before any work begins, and we answer your questions about materials and timeline.

Step 2: Once you approve, we pull any required permits through the local building department and schedule the work. On older homes in Wink, access can be tight on narrow lots, and we plan for staging materials without blocking neighbors. If your home is in an HOA or historic district, we coordinate color and profile approvals before ordering panels. Most metal roof replacements take two to four days depending on size and weather.

Step 3: After installation, we clean up thoroughly, haul away old materials, and do a final walkthrough with you. We make sure you know how to care for your new roof and leave the property as clean as we found it. We do not consider the job done until you are satisfied.

Pricing for metal roofing in Wink depends on the size and complexity of your roof, the material you choose, and the condition of the existing structure. As a ballpark, metal roof installation starts at $8 per square foot, standing seam at $10, metal roof replacement at $9, and metal roof over shingles (retrofit) at $7. Corrugated and ribbed panel roofing starts at $5.50 per square foot, and metal shingle or stone-coated steel at $9. For repairs, metal roof repair and leak repair start at $450, screw replacement and re-fastening at $750, and flashing or chimney repair at $600. Metal roof coating and painting starts at $2.50 per square foot. These are starting prices, and we give you a firm quote after inspecting your roof. Call (432) 248-0371 for a free estimate in Wink.

My house near Winkler County Airport has a low-pitched shingle roof that leaks after every big rain. Can a metal roof fix that?
Yes, a metal roof can be a good solution for low-slope roofs when installed with the right panel profile and underlayment. We often recommend a standing seam or corrugated panel with a proper pitch and high-quality underlayment to handle the flat terrain drainage issues we see in Wink. We will inspect your roof and tell you honestly whether a retrofit or a full tear-off is the better path.
A windstorm just peeled back some panels on my shop roof in Wink. How fast can you get out?
We prioritize storm damage calls and can usually schedule an inspection within 24 to 48 hours, depending on weather and workload. Call us at (432) 248-0371 and we will assess the damage, secure the roof if needed, and provide a repair estimate. We document everything for your insurance claim if you choose to file.
What does a typical metal roof replacement cost for a 1,500 square foot home in Wink?
For a 1,500 square foot home with a standard pitch, a metal roof replacement typically starts around $13,500 to $18,000 depending on material choice and accessibility. Corrugated panels are on the lower end, while standing seam or stone-coated steel are higher. We provide a detailed written estimate after a free inspection, so you know exactly what you are paying for.
Do I need a permit for a metal roof in Wink, and who handles it?
Roofing permits are commonly required for a full replacement or re-roof in Wink, and requirements can vary. We handle the permit application and coordinate inspections with the local building department as part of our service. We always verify current rules before starting work, so you do not have to worry about compliance.
My neighbor's tree branches hang over my roof, and I want to install a metal roof. What are the property line rules I should know?
In Texas, you generally have the right to trim branches that overhang your property line, but it is best to talk with your neighbor first to avoid disputes. If your home is in an HOA, check the covenants for any rules about tree maintenance or roof color approval. We can help you understand what is needed for HOA design review if applicable.
Are you fully insured for roofing work at my Wink property?
Yes, Odessa Metal Roofing is fully insured with general liability and workers' compensation coverage.
What maintenance does a metal roof need in Wink's dusty, windy climate?
In Wink, metal roofs should be inspected annually for loose fasteners, sealant wear, and debris buildup, especially after spring wind and dust storms. We recommend checking flashing around chimneys and skylights and clearing gutters to prevent water backup. A periodic coating can extend the life of painted panels, and we offer maintenance inspections to catch small issues before they become leaks.
Why choose us?

Trusted professionals in Odessa

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Odessa

All your work handled by qualified professionals in Odessa

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

243+ Verified Client Reviews in Odessa

⭐⭐⭐⭐⭐ 4.9/5 · 243 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Odessa · Response within 24h · No commitment · ☎ (432) 248-0371

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Odessa ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm